Search:

Type: Posts; User: rj242

Page 1 of 7 1 2 3 4

Search: Search took 0.08 seconds.

  1. Thread: diagnose this

    by rj242
    Replies
    0
    Views
    576

    diagnose this

    I have an 8 gpm pressure pro cold machine (around 400hrs). It has a 1" suction hose supply line with a plastic 1" valve in the line, going to a 200 buffer tank. When I am soaping, every now and...
  2. Thread: ? For Bob

    by rj242
    Replies
    0
    Views
    736

    ? For Bob

    I'm having trouble with asking a question on the ptek rapid response site. It won't let me send a question, because of invalid email address. I have tried two email addresses and it says both are no...
  3. Thread: Generator ?

    by rj242
    Replies
    3
    Views
    766

    Bob, is 1850w the max, or is that run watts that...

    Bob, is 1850w the max, or is that run watts that the hotbox needs? The generator I was looking at has 2200 peak watt, and 1800 running watts. Thanks for the reply.
  4. Thread: Generator ?

    by rj242
    Replies
    3
    Views
    766

    Generator ?

    Will a 2000 watt Honda or Yamaha generator run a 8 gpm hotbox?
  5. Replies
    5
    Views
    909

    Hydro, I think it goes up to 220-230, not exactly...

    Hydro, I think it goes up to 220-230, not exactly sure, and it is raining like hell right now. It is parked in a detached garage.

    Kilo, it is a pressure pro 8gpm. Not sure of any other specs.
    ...
  6. Replies
    5
    Views
    909

    One more question. I have a 8 gpm / 115 v hot...

    One more question. I have a 8 gpm / 115 v hot box. What would be the smallest generator ( watt / amp) that would run the hot box?
  7. Replies
    5
    Views
    909

    Vertical hotbox ?

    I just purchased a vertical hot box for my open trailer. My question is how concern should I be about rain falling into the opening on top?
  8. Replies
    1
    Views
    725

    Replacing packing seals in pumps?

    How often should you replace the packing seals in a General Pump. I have a Pressure Pro (8gpm) with TSF 2021. I replaced the first set of packing at around 400 hrs. Is this about normal every...
  9. Replies
    3
    Views
    1,458

    Also called spindles

    Also called spindles
  10. Replies
    3
    Views
    1,458

    Cleaning pickets?

    How do you clean the outside of pickets (2"X2") on multiple story decks, without the aid of a lift?

    Thanks in advance for any replies!

    RJ
  11. Replies
    5
    Views
    1,852

    You will be smiling with a move to 5.5 gpm, and...

    You will be smiling with a move to 5.5 gpm, and you will do back flips if you try an 8 Gpm. Either of these machines will be leaps and bounds faster than what you are used to. I will advise you to...
  12. Replies
    74
    Views
    12,997

    Maybe I didn't ask my question clearly enough. ...

    Maybe I didn't ask my question clearly enough. When I went from a 5gpm machine to a 8gpm machine, I was advised to use a 3-5gpm injector, with the 8gpm machine. I then learned that this process was...
  13. Replies
    74
    Views
    12,997

    Being my machines are 8gpm, if I went with the...

    Being my machines are 8gpm, if I went with the remote, would I need to use a 8gpm chemical injector? Currently I use a 5gpm chemical injector, with the chemical injector bypass system that Bob sells.
  14. Replies
    74
    Views
    12,997

    I have 8gpm machines, and I currently use a...

    I have 8gpm machines, and I currently use a 3-5gpm injector with the manual bypass system that Bob sells. If I was to get one of these remote systems, would I need to switch back to a 8gpm injector?
  15. Replies
    74
    Views
    12,997

    Do I still use my regular chemical ejector with...

    Do I still use my regular chemical ejector with these remote chemical ejectors, or does Russ's model have a chemical ejector inside the box?
  16. Replies
    74
    Views
    12,997

    Offduty, I have often wished that I had one,...

    Offduty,

    I have often wished that I had one, but didn't know that they existed. Will they last for years or will they routinely break down? Also being I am running 8gpm, will they reduce my flow...
  17. Replies
    11
    Views
    2,786

    I think I have got it figured out. Thanks for...

    I think I have got it figured out. Thanks for all the replies!!!
  18. Replies
    11
    Views
    2,786

    I'm not good with the picture thing. Could I use...

    I'm not good with the picture thing. Could I use a gavl. elbow? I thought I had read that they were rated for like 300psi.

    Thanks again for the assistance..
  19. Replies
    11
    Views
    2,786

    I could connect a whip, but it will have a 90...

    I could connect a whip, but it will have a 90 bend within 6" or so of the connection. I figured the sharp bend would cause the whip line to bust.
  20. Replies
    11
    Views
    2,786

    I just had a thought after I posted the the...

    I just had a thought after I posted the the thread. Could I buy a stainless steel lance and put two 45 degree bends in it?
  21. Replies
    11
    Views
    2,786

    Hard pipe after washer?

    I am working on redesigning my trailer setup. I have an 8gpm/3000 and a 8gpm/3500, both are Pressure Pro machines. I would like to use hard pipe for about 2 feet (with two 45 elbows) coming out of...
  22. Replies
    4
    Views
    1,333

    Thanks for the replies.

    Thanks for the replies.
  23. Replies
    4
    Views
    1,333

    Adding a bigger gas tank?

    I am rearranging my trailer AGAIN, and this time I want to add a bigger gas tank. I bought a red plastic marine 18 gal tank, and I want to tee off the tank and run two 8gpm Pressure Pro machines. ...
  24. Thread: Hose Reels?

    by rj242
    Replies
    14
    Views
    4,852

    I purchased the Titan alum/stainless reel but it...

    I purchased the Titan alum/stainless reel but it didn't come with a reel lock. Do they sell locks for these reels?
  25. Replies
    31
    Views
    12,972

    I know this is an old thread but my machine with...

    I know this is an old thread but my machine with about 900 hrs just had all four belts break. Has anyone figured out a easy way to change these belts? There is no reason for belt replacement to be...
Results 1 to 25 of 165
Page 1 of 7 1 2 3 4